1600 Lumen Trionic LED Front Light with Battery Pack

This manual both shows how you attach the light holder and the light on a Walker (left column below) and also how you attach them on a Veloped (right column below).

In the left-hand photo, A shows the holder attachment parts for a Walker (2 screws + 2 washers). B shows the holder attachment parts for a Veloped (1 screw + 1 knurled nut + 1 nut).

1600 Lumen Trionic LED Front Light with Battery Pack

Attaching the Light Holder

Instructions for a Walker

On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
A1. On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
Loosen both screws with the 5mm allen key included with the LED light.
A2. Loosen both screws with the 5mm allen key included with the LED light.
Remove the two screws from the grip clamp.
A3. Remove the two screws from the grip clamp.
Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
A4. Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.
A5. Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.

Instructions for a Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
A1. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
B2. Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
B3. Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
B4. For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
This photo shows the light holder as correctly attached.
B5. This photo shows the light holder as correctly attached.

Attaching the LED Light to the Holder

Instructions for a Walker

Identify the circular front end of the light holder, with two slots for attaching the light.
A6. Identify the circular front end of the light holder, with two slots for attaching the light.
Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.
A7. Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.

Instructions for a Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
B6. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Identify the circular front end of the light holder, with two slots for attaching the light.
B7. Identify the circular front end of the light holder, with two slots for attaching the light.

Placing the Battery Pack

Instructions for a Walker

Run the longer extension cable along the semi-vertical grip tube of the Walker and secure it with the included velcro strap.
A8. Run the longer extension cable along the semi-vertical grip tube of the Walker and secure it with the included velcro strap.
You can cut the excessive length of the velcro strap with a pair of scissors.
A9. You can cut the excessive length of the velcro strap with a pair of scissors.
Place the battery pack in the rear zippered pocket of the basket.
A10. Place the battery pack in the rear zippered pocket of the basket.

Instructions for a Veloped

Run the longer extension cable along the U-shaped grip bar of the Veloped and secure it with the included velcro strap.
B8. Run the longer extension cable along the U-shaped grip bar of the Veloped and secure it with the included velcro strap.
You can cut the excessive length of the velcro strap with a pair of scissors.
B9. You can cut the excessive length of the velcro strap with a pair of scissors.
Place the battery pack in the rear zippered pocket of the basket.
B10. Place the battery pack in the rear zippered pocket of the basket.

The package contains

The package contains

How to operate the light

How to operate the light

Product Reviews    

  • 1 7

    Simply brilliant!…

    The Veloped Trek works perfectly. It rides over hill and dale. Snow and ice are no problem either. It's a bit bulky, but the main thing is that it handles the terrain. My dog ​​is also thrilled that Mrs. Hen can walk again.…

  • 12 10

    Super…

    Super, super, super…

    Trionic
  • 16 10

    Jan Furze…

    Very handy attachment, I don't use it very often, but it's there when I need it.…

    Trionic
  • 9 10

    Ingenious invention! Brilliant product!…

    MY EMAIL FROM 11/06/2021

    Hello Mr. Kindberg

    I had no idea what to expect, I had never seen the product in real life ... and then this: wow!

    I just unfolded the Veloped and mounted the wheels. I'm so excited about your invention and the quali…

    Read the Full Review 
    Trustpilot
  • 1 10

    Robust innovative products…

    Good products, long life, sturdy and durable. Good design features.…

    Trustpilot
  • 9 10

    Very good choice for a disabled girl, almost 9 years old...!…

    We bought the Trionic Veloped to our daughter. She is nine years old this summer so Veloped is not really suited for her size yet. But, we still think it works very well in terrain and that was exactly what we were searching, for such a long time!
    …

    Read the Full Review 
    Trustpilot
  • 9 14

    The best outdoor rollator on the market…

    The admittedly high expectations of the Veloped (see previous reviews) were easily fulfilled. No other rollator I know is as stable, safe and reliable as the Veloped and so qualified for use in the countryside, woods and forests.
    However, the high s…

    Read the Full Review 
    Trionic
  • 10 4

    Brilliant!…

    I have MND and walking has become more difficult - mainly due to the worry of tripping and balance. Since I have had the walker, I have been able to enjoy going for walks again and can walk much faster with the walker for support. The walker is so …

    Read the Full Review 
    Trionic
  • 14 0

    Best Purchase…

    This was money well spent. I us this everyday and I can go anywhere with it. I have gone on remote trails and sandy beaches. Everywhere I go people ask about this Veloped. If you want your independence back, buy one of these.…

Subscribe to our newsletter!

"> ?>